Book With Us Today!

 

 

Presented here down the page you can locate some sound advice concerning How to Install a Bathtub.

Mounting a bathtub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a brand-new one is also a moderately tough task. If the old bathtub is readily available, the job can move immediately; if you need to open a wall to eliminate the old tub as well as place the brand-new bath tub, the task is much harder. In either case, the project is within a home handyman's skills, although you will require an assistant to vacate the old tub and set in the new one. Ensure you have actually qualified yourself for the job and are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed task, it is better to take into consideration using one prior to you begin. Possibilities are you may require a professional plumber to make tube connections.
This short article will help you install a brand-new bath tub in your restroom if you have currently gotten a brand-new bathtub as well as don't need to alter the arrangement of your previous water pipelines.
Your devices as well as product checklist need to consist of the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipeline Caps


 

Planning for the Installment

First of all, the supporting frame provided with the bathroom must be fitted (if needed) according to the maker's instructions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets device to prevent strain on the bathtub.
Fit the adaptable faucet adapters to the bottom of both taps utilizing 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its final placement.

 

 

Removing Old Taps

If you require to replace old faucets with new ones as a part of your installment, then the first thing you ought to do is disconnect the water system. After doing so, turn on the faucets to drain any kind of water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome as a result of the limited accessibility that is typically the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the continuing to be water that will come from the pipelines. Once the supply pipelines have actually been gotten rid of, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from turning throughout this process. Once the faucets have been eliminated, the holes in the bath/basin will have to be cleansed of any type of old securing substance.
Before carrying on to fit the brand-new taps, compare the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.

 

 

Setting up the Bath tub

Using both wooden boards under its feet, place the tub in the called for placement. The wooden boards are valuable in equally spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 small points.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by examining the level and adjusting the feet on the tub up until the level reads level.
To set up faucets, fit all-time low of the outermost adaptable faucet connector to the appropriate supply pipe by making a compression join; then do the exact same for the various other tap.
Turn on the water system as well as examine all joints and also brand-new pipework for leakages and also tighten them if essential. Fill the bathtub and also check the overflow outlet and the normal outlet for leaks.
Finally, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bath tub must wait up until the tub has been utilized a minimum of once as this will settle it right into its last placement.

 

 

Suitable New Touches

If the tails of the new faucets are plastic, then you will need a plastic connector to stop damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in location between the tap and also the sink. Protect the faucet in position with the producer offered backnut. Once the faucet is safely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The previous kind ought to be connected to the faucet ends first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.

 

 

Tiling Around the Bath tub

In the area where the bathroom fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to break an inflexible seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, leading to issues with dampness and also possible leakages to the ceiling below.
You can select from a variety of coloured sealers to blend in your components and installations. They are sold in tubes and also cartridges, and can sealing voids up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to sealing, to permit the movement experienced when the bathtub remains in usage. The sealant can fracture relatively very early if you do not consider this activity prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also quickly available on the marketplace. It is recommended to fit the floor tiles using waterproof or waterproof sticky and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

We had been made aware of that report on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through an acquaintance on another web property. Sharing is caring. Helping others is fun. Thanks so much for your time invested reading it.

Contact